released / freigegeben 2012-05-31-09:53:39:571 utc recommended configuration of plated through holes compactpci general information design iec 61076-4-101 no. of contacts 55 - 220 signal (77 - 308 fully shielded); or custo mised contact spacing 2,0mm test voltage 750v ac contact resistance 20 mohm max. insulation resistance 10 10 ohm min. working current 1 a@70c (see derating diagram) temperature range -55c +125c termination technology compliant press-in clearance & creepage distance 0,8 mm each for fixed connector insertion force per contact: 0,75n max. withdrawal force per contact: 0,15n min. - pl1 acc. to iec 61076-4-101 => 500 mating cycles - pl2 acc. to iec 61076-4-101 => 250 mating cycles ul file e102079 rohs - compliant yes leadfree yes circuit density insulator material material pc (polycarbonate, glass fiber reinforcement 20%) color ral 7032 (grey) ul classification ul 94-v0 material group acc. iec 60664-1 iiia (175 < cti < 400) nff classification i2, f1 contact material contact material copper alloy treatment contact zone bellcore recommended lubricant (ppe) plating press-in zone ni - pl1 acc. to iec 61076-4-101 => au over pdni over n i - pl2 acc. to iec 61076-4-101 => au over pdni over n i - "s4" acc. to harting internal pl => min. 0,06m au / 0,7m pdni / 1,3m ni derating diagram acc. to iec 60512-5 (current carry ing capacity) curve 1 shows raise in temperature curve 2 shows nominal derating date name curve 3 shows reduced values as per iec512 detail. 22/05/12 mte inspec. 22/05/12 td stand. date name 0,60 C 0,65mm 0,70,02 mm min. 25m har-bus? hm male connector electrical load [a] the current carrying capacity is limited by maximum tempera ture of materials for inserts and contacts including termin als. the current capacity curve is valid for continuous, non inte rrupted current loaded contacts of connectors when simultaneous power on al l contacts is given, without exceeding the maximum temperature. control and test procedures according to din iec 60 512-5 tin plated pcb (hal) acc. to en 60352-5 chemical tin plated pcb gold /nickel plated pcb silver plated pcb copper plated pcb (osp) in addition to the hot-air-level (hal), other pcb surfaces a re getting more important. due to their different properties - such as mecha nical strength and coefficient of friction - we recommend the following con figuration of pcb through holes. insertion and withdrawal force mating cycles plating contact zone when using the specified diameter of the finished through ho le according to iec 61 076-4-101 (0.6 0.05 mm) with an appropriate annula r ring, the remaining distance between the rings is about 1 mm. under the condition that the width of the track and the space b etween should be equal, two tracks of 0.2 mm width or three tracks of 0 .14 mm width can be placed between two rings. typical designs are shown in the drawing on the rig ht side. temperature [c] ec01567 ni au plated hole ? plated hole ? cu plated hole ? drilled hole ? mod. harting electronics gmbh & co. kg har-bus? hm male connector ds 17 00 110 0101 technical data sheet 0,70,02 mm min. 25m min. 0,8m 0,60 C 0,65mm 0,70,02 mm min. 25m 3-7m drilled hole ? cu ag drilled hole ? 0,70,02 mm min. 25m 0,60 C 0,65mm 0,1 C 0,3m drilled hole ? cu 0,05-0,12m 0,60 C 0,65mm drilled hole ? sn plated hole ? cu sn cu plated hole ? 0,70,02 mm min. 25m max. 15m 0,60 C 0,65mm subject to change without prior notice, all rights reserved page 1 of 1
|
